Doc inlet temp during regen.

Jan 11, 2020 · Force regen after having dpf filters cleaned and temps are as follows After treatment DPF outlet 1024 After treating DPF intake 1041 After treatment diesel oxidation catalyst temp 640 Is this normal 30min I to regen for catalyst to be so low? Any info appreciated Reply Dcmechanical Location Offline Senior Member Reputation: 396 Thanks Given: 952 7. Start the engine and run a Parked Regen. Monitor DOC inlet pressure and engine speed during the regen. Compare your DOC inlet pressure reading to the screen shots below to identify a possible cause of the fault code. a. If the DOC inlet pressure starts out high above 10 kPa (1.45 psi) and decreases during the parked regen, thisMonitor temperature rise across DOC during regen. Little<br /> or no temperature rise indicates DOC not active.<br /> Monitor DOC inlet temperature. No temperature change<br /> after engine startup indicates sensor problem.<br /> Listen for the ITV to sweep at key up.<br /> Turbo not functioning properly Perform a turbo …NOTE: The sensor box (item 8) contains the SCR inlet and outlet NOx sensors, DPF outlet pressure sensor, and the DOC inlet pressure sensor. 1. DOC Outlet Temperature Sensor. 2. DOC Inlet Pressure Sensor Port. 3. DOC Inlet Temperature Sensor. 4. Front Heat Shield. 5. DEF Nozzle. 6. Exhaust Outlet. 7. DEF Metering Unit. 8. Sensor Box (see note ...

Jan 18, 2020 · Mack MP8 regen issues. 2012 CXU613 with 2012 fault codes so it's not a 2013. Truck arrived at the shop at the beginning of the week. Soot load was level 5. performed a parked regen. DOC inlet temp was bias. DPF outlet temp stayed above inlet temp during regen. Jan 1, 2016 · The step response of DOC- out temperature can be acquired by injecting constant amount (i.e. 50 mg/s) of Diesel fuel into the exhaust pipe upstream of the DOC during different steady states (i.e. constant inlet temperature and mass flow rate of exhaust gas).

During a regen the boost psi should be under 10 psi for engines with out a recirculation valve, with the recirculation valve it will be slightly lower. If boost psi is too high remove the sra and verify the turbo sector shaft sweep. It should be smooth and feel a solid stop both ways (there is a tool for verifying full sweep).

This guide will assist with diagnosing regen related codes and issues for GHG14 DD Engines. Engine Speed 1100 rpm (1275 rpm during first 12 minutes of regen …7. Start the engine and run a Parked Regen. Monitor DOC inlet pressure and engine speed during the regen. Compare your DOC inlet pressure reading to the screen shots below to identify a possible cause of the fault code. a. If the DOC inlet pressure starts out high above 10 kPa (1.45 psi) and decreases during the parked regen, this Thank you for input again, however, i forgot to mention at the very beginning that turbo speed at 58,000 - 60,000 rpm which mean in the boost rate, but DOC and DPF at 350, 400 and 430 degree after 30 minute of regen, but after i detect CAC leak on both side, i replaced CAC and turbo speed back to normal around 42,000-43,000 rpm.On just idling, the truck should be at a 160 degree engine temp and the exhaust should be around 520. As it gets warmer, the exhaust will get warmer. 180 degree truck should have a 600 degree exhaust at idle for this engine and the regen should start activating, the air valve opens, and the truck exhaust gets seriously hotter.

Oct 27, 2017 · 10. Perform a parked regeneration. 11. Once the parked regeneration is completed, review the DOC inlet pressure sensor reading in the log file. Does the DOC inlet pressure reading ever read zero during the parked regeneration?1. Yes; replace the DOC inlet pressure sensor. Refer to section "Removal of the Diesel Oxidation Catalyst Inlet Pressure ...

The peak temperature of type II regeneration was above 1100°C, as shown in the type B curve. From the rising trend of the curve in the figure, it could be seen that the sudden rise of regeneration temperature would have a large thermal impact on DPF, which could be observed even when the inlet regeneration temperature was normal.

temperature from inlet temperature to outlet temp erature. The THC from post injection is assumed to be completely combusted inside the DOC (Chen, P . et al. (2014)).This pdf document provides technical service bulletin (TSB) for diesel engine vehicles with 1-Box or Two-Box emissions package. It explains how to diagnose and repair the Diesel Oxidation Catalyst (DOC) inlet pressure sensor and the DOC itself. It also includes the procedure for performing a parked regeneration.This post show you the steps on how to solve Detroit EPA07 GHG14 engine regeneration DOC inlet temperature unable to ... Note : Complete steps in numerical order. If any of the items below have been previously inspected during this visit, do not ... SPN 3713/FMI 14 High Idle Regen (aborted) – Low Regen Temp; SPN 4077/FMI ALL ...The influence of far post injection in cylinder or downstream injection in the exhaust pipe on the DOC inlet temperature can be negligible (Chen, P. et al. (2014 ... Kim, Y. W., Van Nieuwstadt, M., Stewart, G., & Pekar, J. . Model Predictive Control of DOC Temperature during DPF Regeneration, SAE Technical Paper, No. 2014-01 ...During vehicle operation, active regeneration is performed when the accumulated soot and ash reach boundary limits. In this operation, the particulate soot is ...After DOC reaches operating temperature and stabilizes (see callout 2, graph 8), verify DOCOT and DPFOT signal values are greater than 900°F (482°C). In this graph, DOCOT and DPFOT are less than 900°F (482°C). 2. Verify Diesel Oxidation Catalyst Inlet Temperature (DOCIT) signal value is between 550°F (287°C) to 800°F (427°C).Once the DOC is heated up, it can produce high-efficiency oxidization of the post-injected fuel for the DPF regeneration. Based on the DOC light-off temperature achieved, the in-cylinder post fuel injection along with further modulation of the air system parameters can be used to reach a sufficiently high inlet gas temperature for the DPF ...

You can tell by watching your temperatures during a regen. If your DPF intake is lower then your DPF outlet, and theyre both above 800F, it's called 'inverted temps'which indicate your DOC ...more ...DOC temp looks good but the DPF temp is too low. ... Dd15 does not go past 370 degrees during regen , ... It is in regen zone 2. I started regen. Regen started. DOC inlet go to 750 and both others are around 750 as …2018年4月10日 ... During regen the exh temps are (inlet 739) (after cat 969-978) ... I would think if there was an issue with the DOC the inlet temp would be off and ...If regen is starting in the software (i mean it showing that regen is started and rpm goes up) and your doc inlet temp is not raising more than 380-480 then dosing will not start. Dosing starts after the doc inlet being heated up to 560+. This initial heating depends from turbocharger and intake throttle valve.ASL: DOC Inlet Temperature ASL: DOC Outlet Temperature ASL: ASL: SCR Outlet Temperature ASL: SCR Inlet NOX Sensor After-treatment Outlet NOX ASL: Nox conversion AAS: Fuel Doser In'ection Status ASL: Exgas mass rate 'd Connections (paused} Device LMCM21J MCM21T MCM21T CPC04T MCM21T MCM21T MCM21T ACM21T ACM21T ACM21T ACM21T ACM21T MCM21T ACM21TDOC inlet 500-600F DPF inlet starts to increase once regen starts. DPF outlet will increase after DPF inlet starts building temp and heat transfers through DPF. DPF outlet may peak slightly above inlet temp but should down below the inlet temp. …Typically, outlet temp should stay around 50F below inlet temp. If DPF outlet temp stays above the inlet temp then the DOC isn't working probably. Likely face plugged and allows a rich fuel mixture to burn inside DPF instead of DOC. DPF temp should be in the 1000-1100F range. If DPF temp reaches around 1300F, regen will shut down to prevent damage.

a. If the DOC inlet pressure starts out above 10 kPa (1.45 psi) and decreases during a parked regen, this indicates that the DPFs were plugged and the parked regen has cleared them. Go to step 8. b. If the DOC inlet pressure starts above the pressure specified below and stays high, the DOC is considered plugged. Go to step 9. Table 1. Emissions ...

High DOC outlet temperature for DPF regeneration during the FTP cycle CAT 3126 engine. As seen in the chart, maintaining constant DOC outlet temperature at variable exhaust gas mass flow rate and variable DOC inlet temperature conditions is not a trivial task.During a parked regen on a DD15, the SCR Inlet NOx sensor should be around 200-300ppm. DD13 SCR Inlet NOx sensor is slightly higher around 400-500ppm. The SCR Outlet NOx should be somewhere in the neighborhood of 5-25ppm for all DD Platforms. The other true method in testing the NOx sensors is to perform a regular parked regen, then perform ...Jan 1, 2016 · The step response of DOC- out temperature can be acquired by injecting constant amount (i.e. 50 mg/s) of Diesel fuel into the exhaust pipe upstream of the DOC during different steady states (i.e. constant inlet temperature and mass flow rate of exhaust gas). DOC not active. Monitor temperature rise across DOC during regen. Little or no temperature rise indicates DOC not active. DOC Inlet Temperature Sensor non-responsive. Monitor DOC inlet temperature. No temperature change after engine startup indicates sensor problem. Intake Throttle Valve not functioning properly. Listen for the ITV to sweep at ...[Server Time: 10/03/2022 09:26:18 pm] This Forum is English-Only!!!,... Donations help keep the lights on around here, Thanks in advance...The DPF system is a honeycomb filter, similar to a traditional catalytic converter, that captures and collects particulate soot. The 6.7 Cummins has had a DPF system since halfway through the 2007 model year. 2007.5-2012 models had a completely separate DPF system that sat behind the DOC system. In 2013+ models the DOC and …NOTE: Normal DOC pressure is less than 10 kPa (1.5 psi) for a 1-Box™ emissions package and 13 kPa (1.9 psi) for a Two-Box option. 28. Using DiagnosticLink, monitor DOC inlet pressure while performing a parked regeneration. Refer to section "Performing a Parked Regeneration - GHG17". Does the DOC inlet pressure start out high and stay high? a.Once the DOC is heated up, it can produce high-efficiency oxidization of the post-injected fuel for the DPF regeneration. Based on the DOC light-off temperature achieved, the in-cylinder post fuel injection along with further modulation of the air system parameters can be used to reach a sufficiently high inlet gas temperature for the DPF ...I replaced the DOC inlet and outlet temp sensors along with the DPF outlet sensor and all are reading within 3 degrees of each other when the engine is cold. The exhaust system is good with no leaks. The CAC and intake system tested ok with no leaks. The exhaust temps get up to about 487 degrees when the procedure aborts.DOC inlet 500-600F DPF inlet starts to increase once regen starts. DPF outlet will increase after DPF inlet starts building temp and heat transfers through DPF. DPF outlet may peak slightly above inlet temp but should down below the inlet temp. …

During the DESA NOX sensor test, mine never went above 275ppm inlet and 200 outlet at 1700 rpm. Remember the outlet should always be lower than the inlet due to the DEF being injected into the exhaust prior to the SCR catalyst and passes the outlet sensor on the way out the exhaust pipe. My DPF inlet temp will reach 1250, outlet temp 1200.

Jan 18, 2020 · Mack MP8 regen issues. 2012 CXU613 with 2012 fault codes so it's not a 2013. Truck arrived at the shop at the beginning of the week. Soot load was level 5. performed a parked regen. DOC inlet temp was bias. DPF outlet temp stayed above inlet temp during regen.

Save. ClickClick5 · #9 · Aug 7, 2015. EGT3 is the one you will want to watch for the regen. This is the post DPF temp probe. EGT2 is post DOC, and EGT1 is pre DOC. Normal driving, EGT3 will reach around 500-800F. You will know …6. Stay relaxed in a pair of jeans and a windbreaker. Grab your favorite pair of jeans, which will keep your outfit comfortably casual. Slide on a breathable top, along with a windbreaker. Pick out a colorful windbreaker for a more dynamic look, or play around with neutral tones if you'd prefer to be subtle.A) A forced regen will take approximately 40 minutes. It will cycle through 6 stages during this 40 minute period. If the Regen cycle takes longer than this, something else is still wrong. b) During a forced regen cycle, The DOC will get to about 550F, and the doser will activate, first, usually in short intervals, then come on solid.Fengjun Yan. Control of diesel oxidation catalyst (DOC) outlet temperature is critical for downstream diesel particulate filter regeneration, but is challenging to control due to the non-minimum ...The DPF thermal regeneration began at the experimental time of about 30 s, from which the target regeneration temperature and the DPF-inlet temperature started to increase gradually. As soon as the DPF-inlet temperature reached the target temperature of 575 °C, the throttle position was quickly reset and the engine dropped to idle.Exhaust Gas Temp 572, DOC Inlet Temp 572, DPF Outlet Gas Temp 1013 and still the REGEN process did not want to finish. The tech cleared my ash level to see if that would work and nothing. I got some recommended solutions, drop and burn the DPF / DOC, sensors, etc..COOLANT TEMPERATURE: 209F DOC INLET: 432F DPF INLET: 421F DPF OUTLET: 411F Last edited: Jun 10, 2017. 4vmach1, Jun 10, 2017. 4vmach1, Jun 10, 2017 #71 + Quote Reply. Trucking Jobs in 30 seconds. ... During one of the parked regen the delta-p set a out of range on the data monitoring, ...Throttle Valve Actual NOT USED DURING A PARKED REGEN Fuel Comp Pressure 85 ... DOC Inlet Temp 700 – 950 ° F DOC Outlet Temp 1050 – 1150° F DPF Inlet Pressure 0.5 psi – 1.0 psi DPF Outlet Pressure 0.01 psi to 0.9 psi Doser Injection Status gradual increase from 5% to 45% • DOC inlet temp must be at 525° F or higher to

during an engine bench test in this study. Based on the dropped to idle (DTI) test, a test method is developed to determine the safe regeneration temperature of the DPF. The results show that when the inlet temperature of the DOC is more than 240 C, the DOC begins ignition and reaches theSUBJECT: Modified Parked Regeneration Concerns ISSUE The call center has received a number of calls regarding concerns about the modified parked ... modified parked regeneration utilizes increased DOC inlet temperature to clean the DOC inlet face. Excessive torque loads can cause parked regenerations to abort. In some cases the . 19 TS-6 - 4 -Joined: Nov 2011. 6 10-28-2020, 10:36 PM. i have a volvo 2015 d13 with similar issue unit will start regen just fine. but when fuel doser comes up temp 1 is 520 temp 2 starts to climb really fast temp 3 doesnt follow and by the time temp 2 gets to 1000 ( withing 1 minute after doser starts to dose ) it turns off the fuel doser and turbo speed ...6. Start the engine and perform a Parked Regen. 7. Let the regen run for 22 minutes then monitor the DOC inlet pressure. Is the DOC inlet pressure reading at or above 8 kPa (1.16 psi)? a. Yes; the DOC is face plugged. Use the DOC air cleaning tool PN: DSN0ATZ16002. Refer to section "Diesel Oxidation Catalyst Air Cleaning". Verify repair. b. No ...Instagram:https://instagram. phd music therapysteven leonardku basketball women's schedulemike bauer kansas city If regen is starting in the software (i mean it showing that regen is started and rpm goes up) and your doc inlet temp is not raising more than 380-480 then dosing will not start. Dosing starts after the doc inlet being heated up to 560+. This initial heating depends from turbocharger and intake throttle valve.The addition of engine exhaust to intake air increases the over- all heat capacity of the charge, leading to a reduction of peak combustion temperature. Since ... mmj reporterkansas football facility upgrades Mar 7, 2017 · Volvo D13 regeneration. we have couple of trucks on our fleet with the same problem. The forced regen would start but runs indefinetly and not continuously. T he exhaust temp rises to about 500, dpf inlet and outlet reaches up to 920 and then engine suddenly changes tone, shuts of the aftertreatment injector, dpf inlet and outlet temps drop for ... 7. Start the engine and run a Parked Regen. Monitor DOC inlet pressure and engine speed during the regen. Compare your DOC inlet pressure reading to the screen shots below to identify a possible cause of the fault code. a. If the DOC inlet pressure starts out high above 10 kPa (1.45 psi) and decreases during the parked regen, this shocker bookstore 13) Monitor DOC inlet temperature. It MUST be greater than 400°C (750°F). If it is not above 400°C (750°F), block off part of the radiator with cardboard. Be careful that coolant temperatures do not go high enough to cause a Check Engine ight.l 14) Continue to monitor the DOC inlet temperature to make sure it is greater than 400°C (750°F). To create the thermal conditions necessary for soot regeneration in the CSF, fuel was injected into the exhaust pipe up-stream of the DOC (Fig.2). In this study the conditions for fuel injection were fixed to 25ml/min, 300°C inlet temperature and 49,000/hr space velocity for the DOC to generate a CSF inlet temperature of 600C.Regen started. DOC inlet go to 750 and both others are around 750 as well. But diagnostic link never shows that regen goes into regeneration state it always shows engine in thermal management.that is why 7th injector never opens. If i manually open 7th injector,it opens and temp rise as well. But it never opens during regen, no other codes